Natural gas processing removes impurities and the higher value products and prepares a dry gas stream that meets industry standards for transmission in high pressure transmission lines. A facility which performs one of the following: removing water or moisture from the gas stream (i.e. dehydration), removing liquefiable hydrocarbons from wetgas or casinghead gas (i.e. gas processing), removing undesirable gaseous and particulate elements from natural gas (i.e. gas treatment).

Natural gas, as it is used by consumers, is much different from the natural gas that is brought from underground up to the wellhead. Although the processing of natural gas is in many respects less complicated than the processing and refining of crude oil, it is equally as necessary before its use by end users. The natural gas used by consumers is composed almost entirely of methane. However, natural gas found at the wellhead, although still composed primarily of methane comes from three types of wells: oil wells, gas wells, and condensate wells. Natural gas that comes from oil wells is typically termed ‘associated gas’. This gas can exist separate from oil in the formation (free gas), or dissolved in the crude oil (dissolved gas). Natural gas from gas and condensate wells, in which there is little or no crude oil, is termed ‘nonassociated gas’. Gas wells typically produce raw natural gas by itself, while condensate wells produce free natural gas along with a semi-liquid hydrocarbon condensate. Whatever the source of the natural gas, once separated from crude oil (if present) it commonly exists in mixtures with other hydrocarbons; principally ethane, propane, butane, and pentanes. In addition, raw natural gas contains water vapor, hydrogen sulfide (H2S), carbon dioxide, helium, nitrogen, and other compounds.

Natural gas processing consists of separating all of the various hydrocarbons and fluids from the pure natural gas, to produce what is known as ‘pipeline quality’ dry natural gas. Major transportation pipelines usually impose restrictions on the make-up of the natural gas that is allowed into the pipeline. That means that before the natural gas can be transported it must be purified. While the ethane, propane, butane, and pentanes must be removed from natural gas, this does not mean that they are all ‘waste products’. In fact, associated hydrocarbons, known as ‘natural gas liquids’ (NGLs) can be very valuable by-products of natural gas processing. NGLs include ethane, propane, butane, iso-butane, and natural gasoline. These NGLs are sold separately and have a variety of different uses; including enhancing oil recovery in oil wells, providing raw materials for oil refineries or petrochemical plants, and as sources of energy.

While some of the needed processing can be accomplished at or near the wellhead, the complete processing of natural gas takes place at a processing plant. The actual practice of processing natural gas to pipeline dry gas quality levels usually involves four main processes to remove the various impurities:

1. Oil and condensate removal – In order to process and transport associated dissolved natural gas, it must be separated from the oil in which it is dissolved. This separation of natural gas from oil is most often done using equipment installed at or near the wellhead.

2. Water removal – it is necessary to remove most of the associated water. Most of the liquid, free water associated with extracted natural gas is removed by simple separation methods at or near the wellhead. However, the removal of the water vapor that exists in solution in natural gas requires a more complex treatment. This treatment consists of ‘dehydrating’ the natural gas, which usually involves one of two processes: either absorption, or adsorption. Absorption occurs when the water vapor is taken out by a dehydrating agent. Adsorption occurs when the water vapor is condensed and collected on the surface

An example of absorption dehydration is known as Glycol Dehydration. In this process, a liquid desiccant dehydrator serves to absorb water vapor from the gas stream. When in contact with a stream of natural gas that contains water, glycol will serve to ‘steal’ the water out of the gas stream. The glycol solution will absorb water from the wet gas. Once absorbed, the glycol particles become heavier and sink to the bottom of the contactor where they are removed. The natural gas, having been stripped of most of its water content, is then transported out of the dehydrator. The glycol solution, bearing all of the water stripped from the natural gas, is put through a specialized boiler designed to vaporize only the water out of the solution. While water has a boiling point of 212 degrees Fahrenheit, glycol does not boil until 400 degrees Fahrenheit. This boiling point differential makes it relatively easy to remove water from the glycol solution, allowing it be reused in the dehydration process.
A new innovation in this process has been the addition of flash tank separator-condensers. As well as absorbing water from the wet gas stream, the glycol solution occasionally carries with it small amounts of methane and other compounds found in the wet gas. In the past, this methane was simply vented out of the boiler. In addition to losing a portion of the natural gas that was extracted, this venting contributes to air pollution and the greenhouse effect. In order to decrease the amount of methane and other compounds that are lost, flash tank separator-condensers work to remove these compounds before the glycol solution reaches the boiler. Essentially, a flash tank separator consists of a device that reduces the pressure of the glycol solution stream, allowing the methane and other hydrocarbons to vaporize (‘flash’). The glycol solution then travels to the boiler, which may also be fitted with air or water cooled condensers, which serve to capture any remaining organic compounds that may remain in the glycol solution.

Solid-Desiccant Dehydration – Solid-desiccant dehydration is the primary form of dehydrating natural gas using adsorption, and usually consists of two or more adsorption towers, which are filled with a solid desiccant. Wet natural gas is passed through these towers, from top to bottom. As the wet gas passes around the particles of desiccant material, water is retained on the surface of these desiccant particles. Passing through the entire desiccant bed, almost all of the water is adsorbed onto the desiccant material, leaving the dry gas to exit the bottom of the tower.

3. Separation of natural gas liquids

Natural gas coming directly from a well contains many natural gas liquids that are commonly removed. In most instances, natural gas liquids (NGLs) have a higher value as separate products, and it is thus economical to remove them from the gas stream. The removal of natural gas liquids usually takes place in a relatively centralized processing plant, and uses techniques similar to those used to dehydrate natural gas.

There are two basic steps to the treatment of natural gas liquids in the natural gas stream. First, the liquids must be extracted from the natural gas. Second, these natural gas liquids must be separated themselves, down to their base components.

There are two principle techniques for removing NGLs from the natural gas stream: the absorption method and the cryogenic expander process. These two processes account for around 90 percent of total natural gas liquids production.

The Absorption Method – The absorption method of NGL extraction is very similar to using absorption for dehydration. The main difference is that, in NGL absorption, an absorbing oil is used as opposed to glycol. This absorbing oil has an ‘affinity’ for NGLs in much the same manner as glycol has an affinity for water. Before the oil has picked up any NGLs, it is termed ‘lean’ absorption oil. As the natural gas is passed through an absorption tower, it is brought into contact with the absorption oil which soaks up a high proportion of the NGLs. The ‘rich’ absorption oil, now containing NGLs, exits the absorption tower through the bottom. It is now a mixture of absorption oil, propane, butanes, pentanes, and other heavier hydrocarbons. The rich oil is fed into lean oil stills, where the mixture is heated to a temperature above the boiling point of the NGLs, but below that of the oil. This process allows for the recovery of around 75 percent of butanes, and 85 – 90 percent of pentanes and heavier molecules from the natural gas stream.

The Cryogenic Expansion Process – Cryogenic processes are also used to extract NGLs from natural gas. While absorption methods can extract almost all of the heavier NGLs, the lighter hydrocarbons, such as ethane, are often more difficult to recover from the natural gas stream. In certain instances, it is economic to simply leave the lighter NGLs in the natural gas stream. However, if it is economic to extract ethane and other lighter hydrocarbons, cryogenic processes are required for high recovery rates. Essentially, cryogenic processes consist of dropping the temperature of the gas stream to around -120 degrees Fahrenheit. The extraction of NGLs from the natural gas stream produces both cleaner, purer natural gas, as well as the valuable hydrocarbons that are the NGLs themselves.
Once NGLs have been removed from the natural gas stream, they must be broken down into their base components to be useful. That is, the mixed stream of different NGLs must be separated out. The process used to accomplish this task is called fractionation. Fractionation works based on the different boiling points of the different hydrocarbons in the NGL stream. Essentially, fractionation occurs in stages consisting of the boiling off of hydrocarbons one by one. The name of a particular fractionator gives an idea as to its purpose, as it is conventionally named for the hydrocarbon that is boiled off. The entire fractionation process is broken down into steps, starting with the removal of the lighter NGLs from the stream. The particular fractionators are used in the following order:

• Deethanizer – this step separates the ethane from the NGL stream.

• Depropanizer – the next step separates the propane.

• Debutanizer – this step boils off the butanes, leaving the pentanes and heavier hydrocarbons in the NGL stream.

• Butane Splitter or Deisobutanizer – this step separates the iso and normal butanes.

By proceeding from the lightest hydrocarbons to the heaviest, it is possible to separate the different NGLs reasonably easily.

4 Sulfur and carbon dioxide removal.

In addition to water, oil, and NGL removal, one of the most important parts of gas processing involves the removal of sulfur and carbon dioxide. Natural gas from some wells contains significant amounts of sulfur and carbon dioxide. This natural gas, because of the rotten smell provided by its sulfur content, is commonly called ‘sour gas’. Sour gas is undesirable because the sulfur compounds it contains can be extremely harmful, even lethal, to breathe. Sour gas can also be extremely corrosive. In addition, the sulfur that exists in the natural gas stream can be extracted and marketed on its own.Sulfur exists in natural gas as hydrogen sulfide (H2S), and the gas is usually considered sour if the hydrogen sulfide content exceeds 5.7 milligrams of H2S per cubic meter of natural gas. The process for removing hydrogen sulfide from sour gas is commonly referred to as ‘sweetening’ the gas.

The primary process for sweetening sour natural gas is quite similar to the processes of glycol dehydration and NGL absorption. In this case, however, amine solutions are used to remove the hydrogen sulfide. This process is known simply as the ‘amine process’, or alternatively as the Girdler process. The sour gas is run through a tower, which contains the amine solution. This solution has an affinity for sulfur, and absorbs it much like glycol absorbing water. There are two principle amine solutions used, monoethanolamine (MEA) and diethanolamine (DEA). Either of these compounds, in liquid form, will absorb sulfur compounds from natural gas as it passes through. The effluent gas is virtually free of sulfur compounds, and thus loses its sour gas status. Like the process for NGL extraction and glycol dehydration, the amine solution used can be regenerated (that is, the absorbed sulfur is removed), allowing it to be reused to treat more sour gas.

In addition to the four processes above, heaters and scrubbers are installed, usually at or near the wellhead. The scrubbers serve primarily to remove sand and other large-particle impurities. The heaters ensure that the temperature of the gas does not drop too low. With natural gas that contains even low quantities of water, natural gas hydrates have a tendency to form when temperatures drop. These hydrates are solid or semi-solid compounds, resembling ice like crystals. Should these hydrates accumulate, they can impede the passage of natural gas through valves and gathering systems.